Trendnet TEW-637AP Manuel d'utilisateur

1

9 To change IP address, you can select “IP address setting” and click Next button to continue. 10. The default IP address is 192.168.10.100, you ca

12. Select WPS to connect your wireless client device to this AP, and click Next button. 13. Select one of the Wi-Fi Protected Setup methods to

15. To set TEW-637AP security, select Manual setup and click Next button 17. Enter SSID of TEW-637AP, click Next button. 18. To disable Securit

19. To use WEP security, select WEP and click Next button. Select 64-bit or 128-bit WEP key length, and enter your WEP key. For 64-bit encryption, e

21. Save you setting to a text file in a desired location. Page 14

22. Congratulations you have configured you TEW-637AP. Page 15

Using the Configuration Menu Whenever you want to configure your TEW-637AP, you can access the Configuration Menu by opening the Web-browser and typi

Network The Network tab provides the following configuration options: LAN Setting. Network LAN Setting These are the settings of the LAN (Local

The subnet mask of the local area network. Default Gateway The IP address of the router on the local area network. Choose “DHCP (Auto Config)” if

Wireless The wireless section is used to configure the wireless settings for your Access Point. Note that changes made in this section may also need t

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital devic

Radio On/Off Press this button to toggle radio On/off. Page 20

Network Mode If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve perf

This parameter represents transmission rate. By default (Auto) the fastest possible transmission rate will be selected. You have the option of selecti

Wireless Advanced Beacon Interval Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Period val

A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the wireless Access Point has buffe

Wireless MAC Filter The MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their networ

Wireless Security Page 26

SSID choice Choose the SSID which need to implement security. Security Mode You can disable security mode, or you can choose following modes to enable

Wireless WPS You can setup security easily by choosing PIN or PBC method to do Wi-Fi Protected Setup. Page 28

WPS mode Two WPS modes can be selected – PIN & PBC. If PIN is selected, you should enter PIN code of your wireless client device to get wireless c

European Union Notice: Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC Directive (89/336/EEC) and the Low

Wireless Station List You can monitor stations which associated to this AP. Page 30

Administrator This Administrator section is used to set password for access to the Web-based management, also provide function of firmware upgrade. Th

Administrator Upload Firmware By assigning firmware location, you can upload firmware at this page. Page 32

Administrator Settings Management You can save system settings by exporting them to a configuration file, restore them by importing the file, or reset

Administrator Status You can check system information and network configurations on this page. Page 34

Glossary A Access Control List ACL. This is a database of network devices that are allowed to access resources on the network. Access Point AP.

Bandwidth The maximum amount of bytes or bits per second that can be transmitted to and from a network device Beacon A data frame by which one of t

dBd Decibels related to dipole antenna dBi Decibels relative to isotropic radiator dBm Decibels relative to one milliwatt Decrypt To unscram

Extensible Authentication Protocol Encryption Converting data into cyphertext so that it cannot be easily read Ethernet The most widely used tec

GUI Graphical user interface H Half-duplex Data cannot be transmitted and received at the same time Hashing Transforming a string of characters

Table of Contents Getting Started with the TEW-637AP...5 Package Contents ...

In terms of a wireless network, this is when wireless clients use an Access Point to gain access to the network Internet A system of worldwide netw

K Kbps Kilobits per second Kbyte Kilobyte L LAN Local Area Network Latency The amount of time that it takes a packet to get from the one poin

Management Information Base is a set of objects that can be managed by using SNMP Modem A device that Modulates digital signals from a computer to

Network Time Protocol O OFDM Orthogonal Frequency-Division Multiplexing is the modulation technique for both 802.11a and 802.11g OSI Open Systems

PPTP Point-to-Point Tunneling Protocol is used for creating VPN tunnels over the Internet between two networks Preamble Used to synchronize communi

Session key An encryption and decryption key that is generated for every communication session between two computers Session layer The fifth laye

System Logger -- a distributed logging interface for collecting in one place the logs from different sources. Originally written for UNIX, it is now a

Uniform Resource Locator is a unique address for files accessible on the Internet USB Universal Serial Bus UTP Unshielded Twisted Pair V Virtu

Wireless Fidelity Wi-Fi Protected Access An updated version of security for wireless networks that provides authentication as well as encryption

Page 49

Package Contents z TEW-637AP 11n (Draft) AP z CAT-5 Ethernet Cable (the TEW-637AP’s Ethernet ports is Auto-MDIX) z Power Adapter (12.0V, 1.0A) z C

Introduction The TEW-637AP is an 802.11n (draft 2.0) high-performance, wireless AP that supports high-speed wireless networking at home, at work or i

Hardware Overview Auto MDI/MDIX 10/100Mbps LAN Ports This port automatically senses the cable type when connecting to Router. Reset Button

WLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission. WPS LED This LED blinks duri

Getting Started For a typical wireless setup at home, please do the following: 1 Connect one end of the provided network cable into your computer